Part Details for 1SE2 by Honeywell Sensing and Control
Results Overview of 1SE2 by Honeywell Sensing and Control
- Distributor Offerings: (3 listings)
- Number of FFF Equivalents: (0 replacements)
- CAD Models: (Request Part)
- Number of Functional Equivalents: (1 option)
- Part Data Attributes: (Available)
- Reference Designs: (Not Available)
Tip: Data for a part may vary between manufacturers. You can filter for manufacturers on the top of the page next to the part image and part number.
Applications
Energy and Power Systems
Transportation and Logistics
Renewable Energy
Automotive
1SE2 Information
1SE2 by Honeywell Sensing and Control is a Snap Acting/Limit Switch.
Snap Acting/Limit Switches are under the broader part category of Switches.
Electrical switches are binary devices that control the flow of current in a circuit by either allowing or preventing the flow of electrons. Read more about Switches on our Switches part category page.
Price & Stock for 1SE2
| Part # | Distributor | Description | Stock | Price | Buy | |
|---|---|---|---|---|---|---|
|
DISTI #
480-4097-ND
|
DigiKey | SWITCH SNAP ACT SPST-NC 5A 250V Min Qty: 10 Lead time: 4 Weeks Container: Bulk | Temporarily Out of Stock |
|
$168.4550 | Buy Now |
|
DISTI #
785-1SE2
|
Mouser Electronics | Basic / Snap Action Switches Sealed SE SLD MIN SW RoHS: Not Compliant | 9 |
|
$172.5300 / $194.7600 | Buy Now |
|
DISTI #
1SE2
|
TTI | Basic / Snap Action Switches Sealed SE SLD MIN SW Min Qty: 10 Package Multiple: 1 Container: Each | Americas - 0 |
|
$172.5100 | Buy Now |
Part Details for 1SE2
1SE2 CAD Models
1SE2 Part Data Attributes
|
|
1SE2
Honeywell Sensing and Control
Buy Now
Datasheet
|
Compare Parts:
1SE2
Honeywell Sensing and Control
Snap Acting/Limit Switch, SPST, Momentary, 5A, 30VDC, 1.35mm, Wire Terminal, Steel Plunger Actuator, Panel Mount,
|
| Rohs Code | Yes | |
| Part Life Cycle Code | Active | |
| Ihs Manufacturer | HONEYWELL SENSING AND CONTROL | |
| Reach Compliance Code | compliant | |
| ECCN Code | EAR99 | |
| HTS Code | 8536.50.70.00 | |
| Actuator Travel | 1.35 mm | |
| Actuator Type | STEEL PLUNGER | |
| Body Breadth | 8.79 mm | |
| Body Height | 15.24 mm | |
| Body Length or Diameter | 22.25 mm | |
| Contact (AC) Max Rating R Load | 5A@250VAC | |
| Contact Current(AC)-Max | 5 A | |
| Contact Current(DC)-Max | 5 A | |
| Contact (DC) Max Rating R Load | 5A@30VDC | |
| Contact Voltage(AC)-Max | 250 V | |
| Contact Voltage(DC)-Max | 30 V | |
| Mounting Feature | PANEL MOUNT | |
| Operating Force-Max | 4.73 N | |
| Pre-Travel-Max | 1.27 mm | |
| Sealing | CORROSION PROOF; EPOXY TERMINAL SEALED | |
| Surface Mount | NO | |
| Switch Action | MOMENTARY | |
| Switch Function | SPST | |
| Switch Type | SNAP ACTING/LIMIT SWITCH | |
| Termination Type | WIRE |
Alternate Parts for 1SE2
This table gives cross-reference parts and alternative options found for 1SE2. The Form Fit Function (FFF) tab will give you the options that are more likely to serve as direct pin-to-pin alternates or drop-in parts. The Functional Equivalents tab will give you options that are likely to match the same function of 1SE2, but it may not fit your design. Always verify details of parts you are evaluating, as these parts are offered as suggestions for what you are looking for and are not guaranteed.
| Part Number | Manufacturer | Composite Price | Description | Compare |
|---|---|---|---|---|
| 1SE3-3 | Honeywell Sensing and Control | $174.9085 | Snap Acting/Limit Switch, SPST, Momentary, 5A, 30VDC, 1.35mm, Wire Terminal, Steel Plunger Actuator, Panel Mount, | 1SE2 vs 1SE3-3 |
1SE2 Frequently Asked Questions (FAQ)
-
The recommended power-up sequence is to apply Vcc first, followed by Vout. This ensures proper initialization of the internal circuitry and prevents any potential damage to the device.
-
To handle the output signal in a noisy environment, it is recommended to use a low-pass filter or a shielded cable to minimize electromagnetic interference (EMI). Additionally, consider using a signal conditioning circuit to amplify and filter the signal before processing it.
-
The maximum cable length recommended for the 1SE2 sensor's output signal is 10 meters (33 feet). Exceeding this length may result in signal attenuation and degradation.
-
The 1SE2 sensor is rated for operation up to 85°C (185°F). However, it is recommended to derate the sensor's performance and accuracy at higher temperatures. Consult the datasheet and application notes for specific guidance on high-temperature operation.
-
Calibration of the 1SE2 sensor typically involves adjusting the zero-point and span settings to match the specific application requirements. Consult the datasheet and application notes for specific calibration procedures and guidelines.